Vehicles
Sections
473 not categorized PORSCHE 997 CV AXLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1970-73 (includes uncategorized and accessory items) BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection 24135299702YS High efficiency performance and race brake pads for track & street use. These are a high friction pad that are very resistant to heat and are fast to bed-in. Yellowstuff has been used with great success in both race and street cars. Yellowstuff is an aramid fiber-based brake compound with high brake effect even when cold. Yellowstuff is possibly one of the first ever compounds that can be used for street or track driving. These pads do not require warm up but do get even stronger under the heat of hard driving. These are not a low dust pad and if your desire is for a low dust premium street use pad, you should consider ebc redstuff. Features: made for up to 900*c (1,650*f). Developed for race cars but are stree...(choose a part on the right to read more)
$284.90
Make a selection 91135295005EQ If your brake pads are at the end of their service life you will experience vibration, squealing, a pulsating brake pedal or poor response under heavy braking. We recommend replacing them as soon as any of the above signs are noticed. Also, be sure to inspect the rotors when changing the pads. For convenience, we sell complete rotor and pad kits, simply check under brake service kits. This pad set contains textar OEM (original equipment manufacturer) parts that we source in Germany to ensure quality, reliability and precise fitment. Textar brake pads are precision engineered to offer maximum safety, performance and comfort. This uncompromising approach has been the very ethos of textar for more than 100 years. ...(choose a part on the right to read more)
$72.60
Make a selection 240991352GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$654.50
Make a selection 24135191101YS High efficiency performance and race brakes for track and street use, fast to bed-in, great for street vehicle brake upgrade. Not only a high friction pad but very resistant to heat and loads of heavy braking means that yellowstuff has been used with great success in race cars and on street cars. Yellowstuff is an aramid fibre based brake compound with high brake effect form cold and is possibly one of the first ever compounds that can be used for street and tack driving. These pads do not require warm up but do get even stronger under the heat of hard driving. These are not a low dust pad and if your desire is for a low dust premium street use pad, you should consider ebc redstuff. Highlights: made for up to 9...(choose a part on the right to read more)
$199.10
Make a selection 24135291101RS Redstuff brake pads offer significant reduction in stopping distances compared to oe pads. They also reduce annoying brake dust by 60-90%. Plus, the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fiber particles like other pads. The material used in these pads is a kevlar fiber-based brake compound enhanced with ceramic particles. It lasts longer, brakes better and is considerably quieter than OEM or other aftermarket pads. Redstuff pads contain a brake-in coating that accelerates the bed in period. This is a truly impressive high-performance pad for modified European cars, even under repeated heavy braking. Highlights: made for up to 750*c (1,382*f) for street, so...(choose a part on the right to read more)
$171.60
Make a selection BBI9865010001 Features
$845.00
Make a selection 150TB2129 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$603.90
Make a selection 150910160 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location, yet is still quiet and compliant for street use. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new rs sp...(choose a part on the right to read more) General Fitment911 1970-73
From $449.99
Make a selection 240981351RSL2 Pagid yellow rsl 2 are from the rsl line of endurance racing brake pads. They are a medium high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 2 pads are based on the rsl 1 compound but are further improved in terms of pad and disc life and friction stability vs. Temperature. Rsl 2 maintain a constant friction level over a wide range of temperatures. Applications include: GT cars, touring cars, prototype endurance racing and in spring racing. Features at a glance: medium high friction coefficient medium high bite medium high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at t...(choose a part on the right to read more)
$793.10
Make a selection 240991352GRST1 Pagid red rst 1 are from the rst line of circuit racing / sprint racing brake pads. They are a high friction coefficient compound with high initial bite. Rst 1 pads have high temperature resistance, a progressive torque curve and are very fade resistant. They are a semi metallic resin bonded material containing steel and acrylic fibers. Rst 1 pads offer medium pad life and relatively high disc life with moderate modulation. They are suitable for heavy cars where high torque is necessary. Applications include: rally tarmac, GT cars, touring cars, nascar and high downforce formula cars. Features at a glance: very high friction coefficient high initial bite progressive torque curve very fade resistant medium modul...(choose a part on the right to read more)
$680.90
Make a selection 240991351GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$708.40
Make a selection 150TB1126 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$328.90
Make a selection 150TB112801 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: lighter weight tubular / hollow torsion bar set manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$515.90
Make a selection 115900993BI The bilstein b16 (pss10) suspension kit is the ultimate race inspired suspension system, delivering unsurpassed driving performance in any situation. This suspension kit puts you in complete control, providing the kind of precise suspension tuning formerly available only on race cars. From a weekend of competition to daily driving, this system provides perfect handling performance for every situation. The manually adjustable damping mono-tube gas shock absorbers feature 10-stage precise compression and rebound settings, from comfort to competition. The bilstein b16 (pss10) suspension kit utilizes debris resistant round threads on these dampers to ensure spring adjustment remains effortless throughout the life o...(choose a part on the right to read more)
$4,341.70
Make a selection 150TB1130 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle. General Fitment911 1970-73356 1960-65
From $383.90
Make a selection 150TB1127 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle. General Fitment911 1970-73356 1960-65
From $281.91
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |